收藏本站
ISL5216
Tables of Indirect Write Address (IWA) Registers
NOTE: These Indirect Write Addresses are repeated for each
channel. In the addresses below, the * field is the channel select
nibble. These bits of the Indirect Address select the target channel
register for the data. Values of 0 through 3 and F are valid. A channel
select nibble value of F is a special case which writes the data to the
same location in each of the four channels simultaneously.
TABLE 4. CHANNEL INPUT SELECT/FORMAT REGISTER (IWA = *000h)
P(31:0)
24
23
22
21
20:18
17
16
15:13
FUNCTION
Upper Side Band/Lower Side Band select for use in complex input mode.
For complex input mode: when set to 1, the I sample is taken when ENIX is active and the Q sample is taken on the next clock. When
set to 0, Q sample is taken two clocks after ENIX is active.
Complex input enable. Set to 1 for complex input mode, 0 for real input mode.
If set, adjusts the alignment between input data enables and NCO enables to allow unevenly spaced input samples in the gated input
mode. This may be set to 0 to align processing delays with the HSP50216 if necessary.
Floating point exponent saturation level. Used with floating point modes to set the maximum exponent code level 000 to 111. These
bits are protection against overflow due to an invalid exponent for the programmed CIC shift code. Set to 111 to disable.
Enables the new (ISL5216) floating point modes -- the 11, 12, 13 and 14-bit modes with 42 dB of gain, and 15 and 16-bit modes with
18 dB and 6 dB ranges, respectively. The X-1 input must be used for 14, 15 and 16-bit modes. See Floating Point Input Mode Bit
Mapping Tables for details.
Floating point mode select bit 2. Used with IWA *000, bits 8:7 to select the floating point mode/format. See Floating Point Input Mode
Bit Mapping Tables for details.
Channel Input Source Selection - Selects as the data input for the channel specified in the Indirect Address either A(15:0), B(15:0),
C(15:0), D(15:0) or the μ P Test Input register as shown below:
15:13
000
001
010
011
100
SOURCE SELECTED
A(15:0)
B(15:0)
C(15:0)
D(15:0)
μ P Test input register. This is provided for testing and to zero the input data bus when a channel is not in use.
The Global Write Address register for the μ P Test input register is F807h.
12
μ P Test Register input enable selection:
1
0
Bit 11 of this register is used as the input enable.
A one clock wide pulse generated on each write to lGWA F808h is used as the input enable.
Select 0 to write test data into the part.
Select 1 to input a constant or to disable the input for minimum power dissipation when an NCO/mixer/CIC section is unused.
11
μ P input enable. When bit 12 is set, this bit is the input enable for the μ P Test Register input. Active low:
0
1
Enabled
Disabled.
10
Parallel Data Input Format:
0
1
Two’s complement (-full scale = 1000...0000, zero = 0000...0000, +full scale = 0111...1111).
Offset binary (-full scale = 0000...0000, zero = 1000...0000, +full scale = 1111...1111).
9
Fixed/Floating point:
0
1
Fixed point.
Floating point. The 17-bit input bus is divided into 11 to 16 mantissa bits and 1 to 3 exponent bits depending on bits 17,
16, 8 and 7. See Floating Point Input Mode Bit Mapping Tables for details.
8:7
Floating point mantissa size select bits 0 and 1. See Floating Point Input Mode Bit Mapping Tables for details.
34
FN6013.3
July 13, 2007
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ISL5217EVAL1 EVALUATION BOARD FOR ISL5217KI
ISL5239EVAL1 EVALUATION BOARD FOR ISL5239
ISL5239KIZ IC LINEARIZER PRE-DISTORT 196BGA
ISL5416EVAL1 EVALUATION PLATFORM FOR ISL5416
ISL55005IEZ-T7 IC AMP MMIC BIPO BROADBND SC70-6
ISL55007IEZ-T7 IC AMP MMIC BIPO BROADBND SC70-6
ISL55008IEZ-T7 IC AMP MMIC BIPO BROADBND SC70-6
ISL55009IEZ-T7 IC AMP MMIC BIPO BROADBND SC70-6
相关代理商/技术参数
ISL5216KI 功能描述:上下转换器 QUAD DIGITAL DOWNCONVERTER,IND TEMP,0.8M RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
ISL5216KI-1 功能描述:上下转换器 QUAD DIGITAL DOWNCONVERTER,IND TEMP,1.OMM PITCH BGA PACKAG RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
ISL5216KI-1Z 功能描述:上下转换器 W/ANL QD DIG DWNCNVRTR 1 OM PITCH RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
ISL5216KIZ 功能描述:上下转换器 W/ANNEAL QD DIGTL DWNCNVRTR IND TEMP RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128
ISL5217 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Quad Programmable Up Converter
ISL5217_05 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Quad Programmable Up Converter
ISL5217EVAL1 功能描述:EVALUATION BOARD FOR ISL5217KI RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796
ISL5217KI 功能描述:上下转换器 196BGA,-40+85C PROGRAMMABLE QUAD UP CONVERTER RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128